The last fuel tank, port forward, came out today. It was the most difficult to extract for several reasons: it's under the settee and galley cabinet; the fixed-sole extends over the port tanks more than the starboard; this tank has the most floor joists bearing on it—therefore it's the tightest fit; and, the fiber-glassed-in packing gland support gets in the way. I'd been warned by Allan Seymour, Sally W. (42), that this might happen. The yard took his support out and all the fiberglass grinding left quite a mess. The tank, which must be brought aft and then slid athwart into the Starboard aft tanks old slot, jams under the settee. I used a hydraulic car jack to lift the settee. With the settee elevated a little the tank was worked aft until it's forward inboard edge cleared the bearing.
There is lots of rust on this tank but its confined to specific areas. As with the other tanks the worst spot is along the length of the fiberglass band used to hold the in. There were three rusted regions on the tank's top: under the refrig; under the galley window; and under the middle window.
3:54 hours labor today and 13:29 hours to remove the fuel tanks.
Monday, June 27, 2011
It took 13.5 Hours To Remove the Fuel Tanks
Saturday, June 25, 2011
Use Tide to Degrease a Fuel Tank
With a neighbor's help the aft port fuel tank is off the boat.
John Olsen, S/V Daydreamer, recommends using Tide to clean out the tanks—that's what he used in the Alaskan oil patch. John also noted that if aluminum tanks are used, the LNVTs copper fuel lines and manifold can still be used but a stainless fitting will needed to be used to prevent any direct copper-to-aluminum connections. Aluminum tanks would indeed be lighter as mild steel is three times heavier than aluminum. Need to pressure check the repaired tanks (at no more than 3 psi).
1:00 hours labor today and 6:45 hours to date
John Olsen, S/V Daydreamer, recommends using Tide to clean out the tanks—that's what he used in the Alaskan oil patch. John also noted that if aluminum tanks are used, the LNVTs copper fuel lines and manifold can still be used but a stainless fitting will needed to be used to prevent any direct copper-to-aluminum connections. Aluminum tanks would indeed be lighter as mild steel is three times heavier than aluminum. Need to pressure check the repaired tanks (at no more than 3 psi).
1:00 hours labor today and 6:45 hours to date
Friday, June 24, 2011
Fuel Tank Removal Day #2
Fuel tank replacement project day #2. Using a vibratory cutter (like the Fein Multimaster) it took about 50 minutes to cut the fiberglass away from the tank. Once free the tank slid inboard pretty easily. The exhaust hose makes it impossible to get the tank out. Removing the exhaust hose from the muffler and then running it along the starboard cabinets means there's room to get the tank out. Noticed some small cracks along the top of the exhaust hose but underneath was some major damage. It'll have to be replaced.
Things needed:
After a total of 2:00 hours work today, and 4:40 hours total, the starboard aft tank is out. Bicki and I were able to muscle it onto the stern and then with a friend's help we got it off the boat. So far moving the tanks off the boat has been the hardest part of the job.
After another 0:55 hours, mostly to cut the fiberglass and reroute some wires, the aft port tank is free and now sits in the space once occupied by the aft starboard tank.
3:05 hours labor today and 5:45 hours to date.
Things needed:
- 23' of 3" I.D. Marine Exhaust Hose
- 17.5' of 1.5" I.D. Marine Fuel Hose (from deck plates to tanks)
After a total of 2:00 hours work today, and 4:40 hours total, the starboard aft tank is out. Bicki and I were able to muscle it onto the stern and then with a friend's help we got it off the boat. So far moving the tanks off the boat has been the hardest part of the job.
After another 0:55 hours, mostly to cut the fiberglass and reroute some wires, the aft port tank is free and now sits in the space once occupied by the aft starboard tank.
3:05 hours labor today and 5:45 hours to date.
| Just as Tommie Chen said, the tanks can be removed |
| With the fiberglass removed it's obvious that there was some corrosion going on here |
| The aft port tank after it has been moved into the already removed aft starboard tank's space. It's ready to be stood on edge and moved off the boat |
Thursday, June 23, 2011
Fuel Tank Removal Day #1
Fuel tank replacement project day #1. To help others in the fleet I'll keep track of the labor hours it takes to do this project. The stern two tanks are already empty of fuel. Step one is to pull up the floor boards. I've got a feeling this project will breed many others as all ready I can see that the sound dampening insulation under the floor boards can use some work. Next the floor joists are removed. The Phillips stainless screws holding the joists down strip-out easily. I used a Dremel tool with a small grinding wheel to cut a slot into several of the screws. Two of the joists couldn't be removed at all; one goes under the refrigerator while the other goes under the settee. If necessary they can be cut, but I think the tanks will slide under them. In two places wood blocks were wedged between a joist and a fuel tank. The blocks were of different thicknesses and it appears Ocean Eagle Yachts used these to level out the floor. Fuel lines were removed next.
Some thoughts: The least risk approach for tank replacement is not to start over with a new material and installation method, but to build on the 25+ year history. In fact, by repeating what worked and striving to eliminate the causes of the exterior tank corrosion, there's reason to believe the tanks will last longer than 25 years. Here's how I think our tanks are failing, water leaking by a deck fastener, because the fastener missed the deck batten, is getting beneath the tank and then pooling behind the fiberglass tab holding the tank in place.
2:40 hours labor today and 2:40 hours to date.

The Multimaster is the right tool to cut the fiberglass away from the tanks.
The wet exhaust hose is up tight against the aft starboard tank. It will be disconnected from the muffler and moved out of the way.
Picture of the salon looking aft. All the floor boards are removed and a few of the joists too.
Some thoughts: The least risk approach for tank replacement is not to start over with a new material and installation method, but to build on the 25+ year history. In fact, by repeating what worked and striving to eliminate the causes of the exterior tank corrosion, there's reason to believe the tanks will last longer than 25 years. Here's how I think our tanks are failing, water leaking by a deck fastener, because the fastener missed the deck batten, is getting beneath the tank and then pooling behind the fiberglass tab holding the tank in place.
2:40 hours labor today and 2:40 hours to date.
The Multimaster is the right tool to cut the fiberglass away from the tanks.
The wet exhaust hose is up tight against the aft starboard tank. It will be disconnected from the muffler and moved out of the way.
Picture of the salon looking aft. All the floor boards are removed and a few of the joists too.
Friday, June 17, 2011
Balmar ARS-5 Smart Regulator Replacement
Replaced the Balmar ARS-5 alternator regulator with a new one. The old one's potting had cracked and Balmar gave us an RMA for a replacement. When the replacement comes it'll be kept aboard for a spare.
Saturday, May 14, 2011
Bulbs, Batteries and Filters
Installed new spreader light bulbs. Charged the dinks battery and installed new connectors for the dinks sounder to battery connection. Installed new 2 Micron Racor filters and Cummins diesel filter. Sewed up screens for the pilothouses' two opening front windows.
Friday, May 13, 2011
Raw Water Impeller Self Destructs
New dodger. New impeller in both the Cummins and Onan. The Onan's impeller had completely disintegrated while the Cummins' was missing five of its vanes. Had to flush the raw water backwards to get the three pieces lodged against the oil cooler out. Rotated the downstairs AC unit. Much better air flow.
Subscribe to:
Posts (Atom)