Wednesday, May 8, 2019

Part 1: Installing the Rebuilt Fuel Injector Pump

Tightened the four bolts holding the block inspection port in place.  With the injection pump out they're easy to get to.  This should help sterm the small oil leaks from around the plate's rubber gasket.



Withdrew the top dead center (TDC) pin which had gotten stuck in the TDC engaged position.



Changed the engine-mounted (secondary) fuel filter and filled the newly installed filter using the lift pump's manual pump lever.  When the engine is at TDC, the manual lever pumps just fine.  At other piston positions, the fuel pump cam disables the manual lever.


John Mackie, John William 37VT68, said that while removing the injection pump he dropped the pump's lock washer into the engine.  To retrieve it required dismantling the whole front of the engine.  To prevent a similar occurrence I now stuff paper towels in any engine openings.


Now all I have to do is torque the 7/8" bolt to 48 ft-lbs and to remember to remove the paper towels before closing up.  Ok, done.

An always perfectly good raw water impeller is changed at the beginning of every season.  


The logic?  I'd rather replace a perfectly good one now than a failed one in the middle of a nausea inducing seaway.  The picture shows which way the blades should be going.

The injector nuts' torque requirement is 44 ft-lbs.  They all went in easily.  

Next up, attaching the return fuel tube to each injector.  The tube is visible in the picture below (it has green tape on each port).


Copper washers go on each side of the tube.  Fortunately, Cummins offers the two washers attached to a strap.  They're worth the $1/each.






Monday, February 18, 2019

Velvet Drive Internal Strainer

According to the Velvet Drive Manual the 71C, with 2.57:1 gear reduction, has a 2.5 quart capacity:


   I'm glad I went through the manual because page 8A4 states there's a strainer, inside the transmission, at the oil cooler supply attachment point.


In 13 years of ownership I've never checked the strainer.  Oops...






Saturday, January 12, 2019

Rebuilt Cummins Fuel Injection Pump


I picked up Nellie's rebuilt fuel injection pump at J.G. Parks yesterday.  I though there was a mistake as it looked brand new.  They even replaced the metal placard with the engraved part number and serial number.  The cost was $854, $200 more than I paid in 2014 at Nozzle Masters in Orlando, but J.G. Parks replaced about $300 worth of parts, including the main drive shaft.

I got the four fuel injectors back yesterday too.  They were in a million pieces!  I'd asked them to quote a rebuild but balked at the $400 estimate.  The tech told me yesterday that to provide an accurate estimate they tore the injectors apart.  When I passed on their price, they passed on putting them back together.  I guess that's fair but not what I'd envisioned.  The good news is I've already purchased 5 rebuilt injectors at a total cost of $140.  Looking on the bright side, after seeing the injectors apart I now know how they work.

Saturday, June 30, 2018

Finding the Engine Overtemp Problem


Engine Gauge Display after Engine Warmup

Removed some paint between the engine block and it's ground wire.  Then applied aluminum antisieze to all the surfaces.  The water temperature gauge now reads  (sort of) correctly 190°F vs. 180°F.

Friday, June 22, 2018

Fuel Injector Leak

Looking Up from Underneath the Fuel Injection Pump

Nellie has been leaking a little fuel (enough to wet-out a napkin in a 50 mile run) somewhere near the injection pump's distribution lines.

A small drop of fuel can be seen hanging from the injector tube support bracket.  The likely culprit is a loose connection or bad washer between the injection tube and the pump.

Friday, June 15, 2018

Cummins 4BT Water Pump

Telltale of a Leaking Water Pump 


During the morning engine check I found that the water pump's shaft seal had started leaking.

I replaced the pump with a used spare we had on board. A few days later I purchased a new one at NAPA for $54.

Trying to find a water pump for your 4BT3.9M? At an autopart's store tell them you've got a 1991 Dodge D250 w/ 5.9 Cummins turbo.

The Cummins parts catalog for the 4BT3.9 lists the following for water pumps: 3802004 and 3913432.

3802004 crosses to a NWP 557145 in NAPA numbers.

3913432 crosses to a TFP 41181 in NAPA numbers.

Sunday, June 10, 2018

Conductive Grease


Years ago a friend at the Long Beach Naval Station gave me some conductive grease.  He said it was commonly used to both seal out salt air and improve the conductivity of electrical contacts.  I've been looking for the stuff ever since.  

Today, while putting (aluminum based) antisieze on the raw water pump's bolts it dawned on me that this is what the Navy electricians were using.  I put an Ohm meter across some of the stuff and sure enough, it's conductive.