Today we began by sanding down the ridge of 2000E left behind when the bootstripe masking tape was removed. As the picture above shows, the 2000E ends just beneath the upper side of the bootstripe. Thus it's important that the transition between the 2000E and bootstripe be as smooth as possible.
To my surprise we used two gallons of 2000E today. While we could have gotten away with 1-3/4 gallons it was nice to have extra to go back and thoroughly cover voids and pinholes.
I'm disappointed in my fairing job. The shiny 2000E makes every void obvious. A long board rather than a random orbital sander should have been used.
Tuesday, July 1, 2014
Saturday, June 28, 2014
Coat one: Interlux 2000E
![]() |
| After each barrier coat the bootstripe tape comes off an the ridge is sanded |
![]() |
| Pencil marks from the factory in the glass. |
![]() |
| 17288 stamped number in the prop |
Tuesday, June 24, 2014
The Last Sand
Today we sanded off 90% of the fairing material that was applied yesterday. A 5" random orbital sander with 80 grit paper doesn't have enough power to cut through the filler quickly. Whereas an angle grinder with the same paper rips through the job. After the sanding was done we washed the boat (yet again).
As the photo attests, our trunk contains all the tools necessary for a DIY bottom job.
As the photo attests, our trunk contains all the tools necessary for a DIY bottom job.
Sunday, June 22, 2014
Fairing On Again
| Lots of fairing on the starboard bow |
The second fairing coat went on today. Fairing seems to beget fairing as the filled areas make surrounding voids more visible. Gotta remember the mantra, better is the enemy of good enough.
Friday, June 20, 2014
What, Sanding Again?
Not sure why but we both thought sanding the Interlux filler would be easier. Actually it did come off easily enough, it was just that there was so much of it. Being up-close and personal also helped us spot more areas requiring fill. We used a 5" random orbital with 80 grit and a 7" angle grinder with 60 grit. Hands down the better tool was the angle grinder. Dust covered Nellie yet again, so the last job was to wash her with soap and water.
The idea now is to make each coat of Interlux 2000E 1/2" higher up the waterline than the previous coat. The last coat will be about 1/2" below the top of the bootstripe.
The idea now is to make each coat of Interlux 2000E 1/2" higher up the waterline than the previous coat. The last coat will be about 1/2" below the top of the bootstripe.
Thursday, June 19, 2014
Fairing
The Interlux two-part fairing goes on very nicely. It was ~85F today and so the epoxy fairing was firing quickly. Lost some of the first batch but never had a problem after that.
| The fairing is used to smooth any gouges. |
| Paying special attention along the water line |
Tuesday, June 17, 2014
Sand and Wash--Part II
After one more lap checking for blisters the hull and bulwark were washed with soap and water. Tomorrow before beginning to fill we'll wash the areas again with acetone.
A few of the holes I'd drilled in the shoe were overflowing with water. After drying the holes out as best as possible with a paper towel, heat, via a heat gun, was they applied. The holes were then filled to the top with epoxy.
Learned from Phil to use a 1/4" nap roller to apply the Interlux 2000E as a thicker nap may leave ridges. The first coat of 2000E will use a lot more material than subsequent coats. The guesstimate was 2 gallons versus 1-1/4 for coats 2, 3, 4, and 5. Yea, five coats in all. Can put on two coats per day--about 8 hours between coats. The first coat will be white, then gray, then white... I'm thinking about running the 2000E right to the top of the bootstripe.
A few of the holes I'd drilled in the shoe were overflowing with water. After drying the holes out as best as possible with a paper towel, heat, via a heat gun, was they applied. The holes were then filled to the top with epoxy.
Learned from Phil to use a 1/4" nap roller to apply the Interlux 2000E as a thicker nap may leave ridges. The first coat of 2000E will use a lot more material than subsequent coats. The guesstimate was 2 gallons versus 1-1/4 for coats 2, 3, 4, and 5. Yea, five coats in all. Can put on two coats per day--about 8 hours between coats. The first coat will be white, then gray, then white... I'm thinking about running the 2000E right to the top of the bootstripe.
Subscribe to:
Posts (Atom)





