Monday, January 7, 2013

Paint and Poly...

Sanded and applied two coats of satin Minwax Polyurethane to the pilot houses' bench seat. Sanded and put one coat of Cetol on the Dutch door jams. Painted the two diesel deck fill plates yellow and two water deck fill plates blue. Painted the 2M and AM/FM antennas white. Wispy fiberglass strands were starting to show on each. Made new fiberglass screens for each small opening port.

Sunday, December 30, 2012

New Anchor Wash-down Pump Operating Procedure

It appears the water being trapped on the outboard side of the port engine bed was coming from some loose fittings in the potable water line. The water heater sits on a little platform in the engine room.

It appears that the bilge pump hoses used to be routed under this platform. For some reason the hoses are now routed awkwardly next to the water heater. Need to reroute them under the platform.

Successfully tested the newly plumbed anchor wash down system. Changing the operating procedures to leave the wash down's thru-hull, which is located next to the engine's raw water thru-hull closed. It will need to be opened before using the wash down pump.

Saturday, December 29, 2012

Raw Water Flow Rate at Idle RPM is 3 GPM

Replaced the port dinghy davit's magnetic cut-out switch. Ironic as it may seem the old switch was crushed by the magnet--the same magnet that supposed to stop the winch when it comes in proximity to the switch. Bottom line, nothing is more effective than a vigilant operator.

Repaired the dinghy's port fuel tank tie-down; one of the screws had pulled out of the fiberglass floor. Ran the Onan and turned it off and on several times (after a long layoff the impeller is more likely to fail the second time the Onan is run). Measured the cooling water flow rate at the expected 3 gpm.

Friday, December 28, 2012

Bad Fireboy Propane Sensor

The Fireboy S2-A, mounted in the galley and used to turn on/off the propane and warn of gas leaks, has a bad sensor. The bilge mounted MS-2 sensor has been false alarming a lot. Today it quit working totally. Need a new sensor.

About 1/2 gallon of rusty water in the mid-bilge. I need to find a way to drain the water trapped around the ballast. Unless I think of something else, an exploratory hole perpendicular to the bilge may uncover something.

Thursday, December 27, 2012

Bow Thruster Fries Battery Switch...Oops

The Cummins heat exchanger was leaking a little from it's aft-facing inspection plate. This is the same plate I'd removed several days ago to see if there were zinc bits inside the heat exchanger. Tightening the plate's attachment bolt took care of the problem.

 The battery switch being used to isolate the thruster/windlass couldn't handle the bow thruster's current draw—we need a new switch that can handle at least 425A. In the mean time one of the switche's studs is connecting together the battery and the thruster/windlass power line.

Wednesday, December 26, 2012

Tools Down!

Cleaned the bilges. Put several coats of Cetol on the dinghy oars. TSP'd the salon walls, companionway hatch interior, and the Tommy door. Removed the wood mounts in the pilothouse that supported Peter Newman's writing table. Updated the Garmin MFDs to software V7.5. And, finally, after six weeks we put all the tools away!

Tuesday, December 25, 2012

Draining the Airsep's P-Trap

For the record, all of the following occurred after opening Christmas presents.

Washed the decks with Oxy.

One more bung came off during the scrubbing which leaves three that need to be repaired. Put a new impeller in the Cummins. The old impeller was in good shape.

Drained oil out of the AirSep's p-trap. Need to add this task to the Periodic Maintenance List. It probably should be checked every six months.

 The dinghy tube repair seems to be holding. Yea! The repair methodology was different this time in that (1) toluene was used to scrub the patched area; (2) three coats of contact adhesive were applied with a paintbrush; and (3) the tube wasn't inflated for 24 hours.