Got the salon's starboard forward and starboard middle windows back in. Black GE Silicon II caulk was used between the inner window retainer and the stainless frame as well as between the outer window retainer and the stainless frame. The same caulk was used between the non-movable window and its retainer (i.e. the outer retainer) to lock the window in place. If the screws holding the retainers leak, water will find its way into the void between the salon's outer fiberglass wall and the wood of the inner wall. This may be where Nellie's port side leak is. Clearly the screws which cause the most concern are the ones that water naturally pools on, i.e. those on the bottom of the window. The inner retainer has no screws on the bottom--just two on the forward side and one on the aft. The outer retainer has three screws on the bottom. Two of these can't be serviced as they're covered by the fixed pane. I caulked closed those two holes and didn't put screws back in them--I fear leaks more than I fear the loss of strength from the missing two screws.
Got the third and last coat of Helsman Spar Urethane on the outward facing edge of the teak window frames.
Cut the water drainage slots through the Trim-Lok U-channels.
Monday, December 17, 2012
Sunday, December 16, 2012
Replacement Window U Channel--Trim-Lok
Used a bead of Locktite PL S40 (polyurethane caulk) between the window's stainless u-channel (aka the inner retainer) and the Trim-Lok rubber u-channel. The S40 works great holding the rubber u-channel inside the stainless u-channel. To get the Trim-Lok to form tightly to the window's corners I heated it with a heat gun. This relaxes the Trim-Lok so it can easily be pushed right into place. Masking tape kept the Trim-Lok firmly seated in the retainer until the S40 dried. Once dry the ends of the Trim-Lok, which had been left long, were cut even with the the ends of the inner retainer.
Got the third and final coats of Helmsman Spar Urethane on the inward facing edges of the teak window frames. I was finally able to get the urethane to flow pretty well. The trick was to dip the brush in urethane and then, starting about four inches in front of the wet edge, stroke the brush back into the wet edge.
Everything in the stateroom, except the doors, got its first coat of Minwax semigloss polyurethane.
Got the third and final coats of Helmsman Spar Urethane on the inward facing edges of the teak window frames. I was finally able to get the urethane to flow pretty well. The trick was to dip the brush in urethane and then, starting about four inches in front of the wet edge, stroke the brush back into the wet edge.
Everything in the stateroom, except the doors, got its first coat of Minwax semigloss polyurethane.
Saturday, December 15, 2012
Valspar Flat Dove White Latex on the Walls
Sanded everything in the stateroom that has a polyurethane finish—which is a lot! Put the third coat of Lowes Valspar Dove white on the stateroom's port side wainscoting. Sanded the louvered doors under the galley sink.
Sunday, December 9, 2012
Paint on Runrail
Repainted the teak rubrail black.
Saturday, December 1, 2012
Grease and Caulk
Filled fastener holes in the stack with polyester putty. Put a new pencil zinc in the heat exchanger. Greased the Bomar hatches, the windlass, and the rudder shaft. Recaulked the wind instrument mount.
Friday, November 30, 2012
New Raritan Water Heater
Finished installing the Raritan 170611 6 gallon water heater. Repaired the small coolant leak at the top of the riser (above the hose which goes from the engine to the hot water heater). Finished painting the rub rail black.
Thursday, November 29, 2012
Water Heater Leaks
Removed the the old water heater. Found that coolant had been leaking from the h/w tank's heat exchanger feed point. It was running down along the tank's insulation and then dripping into the bilge. Started installing the Raritan 170611 6 gallon water heater.
Started painting the rub rail black.
Started painting the rub rail black.
Subscribe to:
Posts (Atom)